Remember urea formaldehyde foam insulation (UFFI)? Back in the late 1970s and early 1980s it was the ultimate bad guy of the insulation world. Installed in hundreds of thousands of homes in the U.S. and Canada following the 1973 Energy Crisis, UFFI was found to emit high levels of formaldehyde in some circumstances and shrink considerably, resulting in performance problems.
The Canadian government spent millions of dollars insulating 80,000 to 100,000 homes with this insulation, then spent many more millions de-installing it when reports of problems emerged. Canada banned the product, as did the Consumer Products Safety Commission in 1982 in the U.S. -- though the latter reversed the ban a year later.
The industry largely disappeared. While there had been 39 manufacturers of UFFI in 1977 and upwards of 1,500 installers, that dropped to just a handful by the early-eighties. Most of us pretty-much forgot about the product.
UFFI is still around
While most of the UFFI industry disappeared, including two large producers, five companies have continued to produce UFFI, though under different names. Most of those companies have gone to significant effort to avoid any association with UFFI or with formaldehyde.
Among the five manufacturers of UFFI today, you will variously see the material referred to as "injection foam," "amino foam," "aminoplast foam," "tri-polymer foam," "dry-resin foam," and various combinations thereof. The only reference you’re unlikely to see is "urea-formaldehyde," and if you ask manufacturers what the stuff is most will go to great lengths to obfuscate their response.
Used for insulating
The primary application for UFFI today is to insulate hollow concrete block walls -- and I think it is a fairly good solution for such buildings. It can also be used as a retrofit insulation for wood-frame cavity walls, but there are better products for wood-frame construction.
What is it?
To really understand what UFFI is, one may need a degree in polymer chemistry. cfiFOAM, which is the most forthcoming of the manufacturers in production today, describes the material as being "part of the family of amine/furan resins consisting of phenol, urea and melamine, coupled with an aldehyde." A resin is produced that is dried to produce a power that can be stored and shipped.
Insulation contractors use specialized equipment to mix the powdered resin with water, surfactant, and catalyst to create the injectable foam. By carefully controlling the mix of these different components, the release of free formaldehyde -- one of the main problems in the past -- is greatly reduced.
Phosphoric acid is often used in this process, and that chemical imparts some fairly good fire retardant properties. To the best of my knowledge, there are no halogenated flame retardants used in any of the amino foams -- which is a significant benefit of the material.
Consistency of shaving cream
Amino foams are fully expanded at the time of installation -- unlike polyurethane foams, which expand as they are sprayed into a cavity or onto a surface.
The foams are very flowable, and according to Bob Sullivan of cfiFOAM can fill vertically at least 12 feet. The flowability allows the insulation to fill concrete cores very effectively, including around hardened mortar protruding into the cores.
Along with confusing information about what the amino foams are -- and their history as UFFI -- some manufacturers publish misleading claims about performance. The material insulates to about R-4.6 per inch, which is quite good. You may see claims of performance as high as R-5.1 per inch, but if you read the fine print, you’ll find that the higher performance claim assumes measurement at 25-degree Fahrenheit instead of the more standard 75-degree Fahrenheit.
More significantly, you may see exaggerated claims about the resulting R-value of concrete block walls insulated with amino foam. Tailored Chemical Products continues to claim exaggerated R-values above R-14 for 8-inch concrete blocks walls insulated with the company’s Core-Fill 500, a UFFI insulation.
In reality, the R-value of an 8-inch block wall with amino foam depends greatly on density of the concrete. With very low-density blocks -- 85 pounds per cubic foot (pcf) -- two-core, blocks insulated with this insulation provide a "whole-wall" R-value of 11.3. With heavier (more dense) concrete blocks the R-values drop. With medium-density blocks (105 pcf) the whole-wall insulating value drops to R-8.2, and with high-density block (125 pcf), the whole-wall R-value drops to R-6.0. The dramatic difference between the R-value of the foam insulation alone and insulated concrete blocks results from thermal bridging through the concrete webs in the blocks.
The major problem that led to the near destruction of the UFFI industry was the fact that the material can offgas formaldehyde, which is considered a known carcinogen. (Back in 1982, when the Consumer Products Safety Commission temporarily banned the material, formaldehyde was considered a "probable human carcinogen," but the hazard warning has been upgraded to "known carcinogen.")
Formaldehyde offgassing continues to be a concern with amino foams, but improvements in the chemistry by all of the manufacturers has significantly reduced this problem.
Shrinkage of foam
More significant than formaldehyde offgassing, I believe, is shrinkage that can occur with amino foams. Typical shrinkage after installation is 0.5 percent, but in some cases shrinkage can be as much as 2 percent, or even 4 percent according to some sources. According to cfiFOAM, the impact of shrinkage is accounted for in the reported whole-wall R-values by at least that company, but it’s still a big concern.
UFFI (a.k.a. injection-installed amino foam) has some quite attractive features, and I believe these to be a good option for concrete masonry construction. Were it not for the shrinkage and the lack of clear information and transparency by most of the amino foam industry, I might even consider this a "green" option -- especially because it is the only foam-plastic insulation that does not contain halogenated flame retardants.
Alex Wilson is the founder of BuildingGreen, Inc. and the Resilient Design Institute (www.resilientdesign.org), both based in Brattleboro. Send comments or suggestions for future columns to firstname.lastname@example.org.